#Victron bmv 712 smart battery monitor generator
#Victron bmv 712 smart battery monitor update
#Victron bmv 712 smart battery monitor manual
#Victron bmv 712 smart battery monitor Bluetooth

Protection rating IP55 (not suitable for outdoor use)Įmissions / Immunity EN 55014-1 / EN 55014-2īattery voltage, current, state of charge in percent and the auxiliary input (battery temperature, mean value deviation or voltage of the starter battery).Hi are 4 relevant settings here and they all work together. Temperature (0 - 50☌ or 30 - 120☏) ± 1 ☌/ ☏įront panel 69 x 69 mm (2.7 x 2.7 inches)īolts for shunt connections M10 (1 cm / 0.3937 inch)ĭiameter and depth housing 52 mm (2.0 inch) and 31 mm (1.2 inch) RESOLUTION & ACCURACY (with a 500 A shunt) Blogpost Lithium Battery Smart - addendum firmware v1.19 Lithium Battery Smart (HTML5) Lithium Battery Smart (PDF).

#Victron bmv 712 smart battery monitor manual

Measures voltage of a second battery, temperature or midpoint: Yesīistable relay: 60 V / 1 A Normally open (function can be reversed) BMV-712 Smart (HTML5) BMV-712 Smart (PDF) VictronConnect Manual (HTML5). Input voltage range, additional battery: 6.5-70VDC Additional input for measuring voltage (a second battery), temperature or midpoint voltage as well as associated alarms and relay settings. High current measurement resolution 10 mA (0.01 A) Stores a wide range of historical data that can be used to evaluate usage patterns and battery health. Shunt capacity selectable up to 10,000 amps. Blue Sea Systems 6006 m-Series Battery Switch ON/OFF with Knob, Red. Victron Energy Temperature Sensor for BMV-702/712.

#Victron bmv 712 smart battery monitor generator

The system has 800 watts of solar and generator that can charge the battery bank. All of the settings are correct for the battleborn batteries firmware is up to date. Now one would think the SOC would go up and down correctly with the voltage but the BMV-712 shows a low SOC all the time. A 500 amp quick connect shunt and connector kit. This item: Victron Energy BMV-712 Smart Battery Monitor (Black) 19550. At that point I synchronize the BMV to 100. Programmable relay to turn off non-essential loads or a generator if needed to turn on. Remaining running time at current discharge rate

Battery voltage, current, power, amp-hours consumed and state of charge Prevents increased current consumption in the event of an alarm. For example, a residual current of 10 mA can damage a 200 Ah battery if the system is left discharged for over 8 days.

The battery will be damaged if the remaining reserve capacity is drained from the battery. After shutdown due to low voltage, the capacity reserve of a lithium-ion battery is approximately 1 Ah per 1000 Ah of battery capacity. Power consumption: 0.7 Ah per month (1 mA) at 12 V and 0.6 Ah per month (0.8 mA) at 24 V Lithium-ion batteries in particular have almost no capacity left when they are discharged until they are switched off due to low voltage. Very low power consumption from the battery We recommend our Battery Balancer (BBA000100100) to maximize the life of series-connected lead-acid batteries. Please also note the BMV manual, section 5.2 for more information. If batteries are connected in series, measuring the midpoint voltage can generate a timely warning message.

There is also a separate front panel for a square or round display A safety ring for rear mounting and screws for front mounting are included.Ī damaged cell or battery can destroy an entire large, expensive battery bank. Included in delivery: RJ12 cable (10 m) and battery cable with fuse (2 m) No further components are required.

#Victron bmv 712 smart battery monitor Bluetooth

With Bluetooth being implemented in most other Victron. The shunt is connected to the monitor via a standard RJ12 telephone cable. BMV-712 Smart With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era.

#Victron bmv 712 smart battery monitor update

on Update the latest software when new features become available.Īll electrical connections are made using the PCB connector on the power shunt. display all important data on one screen, Using a smartphone or other Bluetooth-enabled device, adjust the Wireless communication between products simplifies system installation and improves performance. With Bluetooth built-in, the BMV Smart is ready for the Internet of Things (IoT) era. Most other Victron Energy products also have Bluetooth. Victron Smart Battery Monitor - BMV 712 Bluetooth Bluetooth inside. With its built-in Bluetooth, the BMV Smart is ready for the age of the “Internet of Things” (IoT). Victron Battery Monitor BMV-712 Smart Shunt (black)